How to pass Cisco 350-601 exam with the help of dumps?

Question # 1

A new employee must be granted access to add VLANs into an existing Cisco UCS Manager and configure NTP synchronization with date and time zone settings. Which two privileges must be granted to the employee to complete the task? (Choose two.)

A. Service Profile Compute (Is-compute)
B. Ext LAN Config (ext-lan-security)
C. Service Profile Network Policy (Is-network-policy)
D. Service Profile Config (Is-config)
E. Ext LAN Policy (ext-lan-policy)

Show Answer

Question # 2

AN engineer is implementing an import operation in Cisco UCS Manager. What is the impact of performing this operation?

A. A configuration can be imported from a higher release to a lower release.
B. Information can be modified on the management plane only.
C. Only a configuration file that was exported from the same Cisco UCS Manager can be imported.
D. An import operation can be scheduled.

Show Answer

Question # 3

Which two actions should be performed before upgrading the infrastructure and firmware of multiple UCS blades? (Choose two) 

A. Verify if the bootflash on the fabric interconnects in the Cisco UCS has at least 15% available space 
B. Enable Smart Call Home feature during the firmware upgrade process
C. Verify if the bootflash on the fabric interconnects in the Cisco UCS has at least 10% available space
D. Run the Check Conformance feature to verify that all your components are running the compatible firmware version after the upgrade
E. Get Full State and All Configuration backup files before beginning the upgrade

Show Answer

Question # 4

Refer to the exhibit.What is a characteristic of the UUID in the service profile presented. 

A. based on the hardware
B. vendor assigned
C. unique system generated
D. allocated from a UUID pool

Show Answer

Question # 5

Refer to the exhibit.  An engineer configures a new application profile using REST API and receives this error massage. Which method can be used before application profile can be configured?

A. POST to aaaLogin
B. POST to aaaRefresh
C. POST to aaaLogout
D. GET to aaaListDomains

Show Answer

Question # 6

An engineer is implementing Cisco Intersight in a secure environment. The environment must use LDAP directory service and ensure information integrity and confidentiality. Which two steps must be taken to implement the solution? (Choose two.)

A. Enable Encryption for LDAP
B. Add a self-signed LDAP certificate to Cisco Intersight.
C. Enable Certificate Signing Request in Cisco Intersight.
D. Add a trusted root LDAP certificate to Cisco Intersight
E. Add a trusted OAuth token to Cisco Intersight

Show Answer

Question # 7

An engineer must configure two Cisco Nexus 7000 series switches in the same data center to support OTV. Which command set completes the join interface configuration?

A. Option A
B. Option B
C. Option C
D. Option D

Show Answer

Question # 8

Refer to the exhibit.  An engineer configures FCIP on a Cisco MDS 9000 Series switch. What is the result of implementing the configuration?

A. The switch attempts to make two TCP connections
B. Compression is performed by using hardware
C. Mode2 is enabled by default.
D. Compression is performed by using software.

Show Answer

Question # 9

Which statement about the impact of a rolling EPLD upgrade on a Cisco MDS 9000 Series Switch is true?

A. All modules on the switch are disrupted.
B. An EPLD upgrade is nondisruptive.
C. Only the modules that are being upgraded are disrupted.
D. The upgrade can be performed from the standby supervisor module.

Show Answer

Question # 10

Port security is enabled on a Cisco MDS 9000 series Switch. Which statement is true?

A. Cisco Fabric Services must be disabled before enabling port security.
B. Port security can be enabled only globally and affects all VSANs.
C. Auto-learning is always enabled automatically when port security is enabled.
D. Any devices currently logged in must be added manually to the device databased.

Show Answer

Question # 11

What are two recommended design choices in a topology for multipathing iSCSI traffic? (Choose two.)

A. two NICs bonded together on the initiator
B. dual initiators to a single target with bonded interfaces
C. initiators and targets in separate subnets
D. dual initiators to dual targets
E. single initiator to dual targets

Show Answer

Question # 12

Refer to the exhibit.An engineer is implementing zoning on two Cisco MDS switches. After the implementation is finished, E Ports that connect the two Cisco MDS switches becomes isolated. What is wrong with the implementation?

A. E Ports on both MDS switches must be configured as F ports for the zoning to function.
B. Zones are local to the MDS switch and name service must be used to activate the connection between E ports.
C. Different zone set names must be configured on both MDS switches.
D. Zones must have the same name on both MDS switches for the E ports to function.

Show Answer

Question # 13

Refer to the exhibit.  Which VLANs are capable to be assigned on vPC interfaces?

A. 100-103
B. 100-104
C. 100-102
D. 100-105

Show Answer

Question # 14

An engineer must configure a Nexus 7000 series switch for HSRP on VLAN 100. When fully functional, the router must be the active master. Which set of commands must be used to implement the scenario? 

A. Option A
B. Option B
C. Option C
D. Option D

Show Answer

Question # 15

An engineer must suggest a deployment model for a newly developed application. The engineer has a small starting budget and lacks technical knowledge and infrastructure to implement store, operating system and database services to support the application deployment. The engineer also needs usage data related to the service and the ability to elastically scale the deployment as customer demands grow. Which two models must be used to meet the requirements? (Choose two) 

A. infrastructure as a service
B. private cloud
C. public cloud
D. software as a service
E. platform as a service

Show Answer

Question # 16

An engineer is running an ACI fabric, has VMM integration with VMware vCenter, and wants to enable microsegmentation based on vCenter VM attributes. Which statement about microsegmentation is true? 

A. ACI does not support microsegmentation based on vCenter VM attributes. You should use network attributes for mircosegmentation. 
B. An ACI microsegmented EPG automatically creates a port group with a private VLAN configured on a VMware vCenter distributed virtual switch.
C. When enabled, microsegmentation performs distributed switching and routing on the ESXi hosts. 
D. Microsegmentation is supported only using AVE or AVS. 

Show Answer

Question # 17

A customer has a requirement to deploy a cloud service and needs to have full control over the underlying OS, data and application. Which cloud model meets this requirement?

A. PaaS
B. MaaS
C. IaaS
D. SaaS

Show Answer

Question # 18

An engineer is asked to manage a large-scale data center and collect information from multiple Cisco NX-OS devices using Cisco NX-OS Data Management Engine model. Which technology should be used to accomplish this goal? 

A. NX-API REST
B. NETCONF
C. JSON-RPC
D. NX Yang

Show Answer

Question # 19

A network engineer repeatedly saves a configuration on Catalyst switches to NVRAM using the write memory command. What action should be taken to implement the same action on Nexus switches?

A. Use the write memory command to save the configuration.
B. Use the alias command to use the write memory command.
C. Use the exit command to leave the configuration mode and save the configuration automatically.
D. Use the wri command to use the copy running-config startup-config command.

Show Answer

Question # 20

An engineer is asked to use SaaS to manage Cisco computing. Which two items are needed to accomplish the task? (Choose two.) 

A. UCS Manager
B. Node name/Serial Number
C. Device/Claim ID
D. UCS Central
E. Intersight

Show Answer

Question # 21

Which event is expected during direct upgrade of Cisco UCS Manager firmware?

A. The I/O Module reboots immediately after the firmware is activated.
B. All users logged in to the UCSM are logged out, and their sessions end.
C. Data traffic is disrupted for a single fabric interconnect setup.
D. IPMI polling is interrupted.

Show Answer

Question # 22

An engineer is configuring a vHBA template in UCS Manager. The engineer needs to specify the logical addresses used by the vHBA and the path through which the SAN traffic flows. Which two resources must be specified in the vHBA template? (Choose two.) 

A. MAC addresses
B. WWPNPool
C. WWNN
D. VLAN ID
E. Fabric ID

Show Answer

Question # 23

Which two methods are available to Manage an ACI REST API session authentication when a user is unauthenticated?

A. POST to aaaLogin
B. POST to aaaUserLogin
C. GET aaaRefresh
D. GET to aaaListDomains
E. DELETE to aaaLogout

Show Answer

Question # 24

What is required for using puppet in a Cisco NX-OS environment?

A. Open Agent Container
B. XML management interface
C. NX-API
D. OpenNP

Show Answer

Question # 25

An engineer installed a new Nexus switch with the mgm0interface in vrf management. Connectivity to the rest of the network needs to be tested from the guest shell of the NXOS. Which command tests connectivity from the shell of the NX-OS? 

A. Option A
B. Option B
C. Option C
D. Option D

Show Answer

Question # 26

A network engineer must configure a power redundancy policy on a Cisco UCS C-Series Rack Server. The power redundancy must support two power sources being used to power the server. Which configuration should be applied to meet the requirement? 

A. Option A
B. Option B
C. Option C
D. Option D

Show Answer

Question # 27

What is a recommended design choice in a topology for multipathing iSCSI traffic? 

A. single initiator to dual targets
B. initiators and targets in separate subnets
C. dual initiators to a single target with bonded interfaces
D. two NICs bended together on the initiator

Show Answer

Question # 28

Which configuration implements static ingress replication?

A. interface nve 1member vni 2100980ingress-replication protocol staticpeer-ip 10.0.0.4
B. interface nve 1member vni 127772151ingress-replication protocol bgp
C. interface nve 1member vni 3126980peervtep 10.0.0.4ingress-replication protocol staticpeer-ip 10.0.0.4
D. interface nve 1member vni 384233213peer vtep 10.0.0.41

Show Answer

Question # 29

What are two requirements when planning a Cisco HyperFlex All Flash standard cluster installation using three HX240c M5 servers? (Choose Two)

A. If the Jumbo MTU option in the HyperFlex installer is enabled, then jumbo frames do not have to be enabled on the upstream switches. 
B. The hypervisors must be installed to Cisco FlexFlash SD cards. 
C. If the Jumbo MTU option in the HyperFlex installer is enabled, then jumbo frames must also be enabled on the upstream switches
D. The cluster deployment type must support a mix of HDD and SSD.
E. The servers must be discovered, unassociated, and connected to each fabric interconnect.

Show Answer

Question # 30

An engineer is implementing FCoE. Which aspect of DCBXP on a Cisco Nexus switch affects this implementation? 

A. It uses the Cisco Fabric Services protocol to exchange parameters between two peer links. 
B. It always is enabled on 10/100-Mbps native Ethernet ports.
C. It provides the authentication of peers on the Cisco Nexus switch.
D. It requires that LLDP transmit and LLDP receive are enabled on the FCoE interface.

Show Answer

Question # 31

In an FCoE environment, for which two sets of data must an interface that implements the PAUSE mechanism always provision sufficient ingress buffer? (Choose two)

A. frames that were sent with high credit
B. frames that were processed and transmitted by the transmitter before the PAUSE frame left the sender
C. frames that were sent on the link but not yet received.
D. frames that were sent on the link and received.
E. frames that were processed and transmitted by the transmitter after the PAUSE frame left the sender.

Show Answer

Question # 32

Refer to Exhibit:  An engineer must use the python module in the guest shell of the Cisco Nexus 9000 Series switch to shutdown port Ethernet 1/4 Which command set will accomplish this?

A. Option A
B. Option B
C. Option C
D. Option D

Show Answer

Question # 33

An engineer must configure multiple EPGs on a single access port in a large Cisco ACI fabric without using VMM integration. The relevant access policies and tenant policies have been created. A single AAEP is used to configure the access port in the fabric. Which two additional steps must be taken to complete the configuration? (Choose two.)

A. A contract must be defined between the EPGs
B. The EPGs must be linked to the correct physical domain
C. The EPGs must link directly to the corresponding AAEP
D. The corresponding bridge domains must be configured in legacy mode
E. The EPGs must be configured as static ports

Show Answer

Question # 34

Which two actions are needed to configure a single Cisco APIC controller for Cisco ACI fabric for the first time? (Choose two.)

A. Register the APIC that is connected to the switch.
B. Configure the first Cisco APIC controller
C. Configure the leaf switch where the Cisco APIC is connected, using CLI to allow APIC connectivity
D. Register the switches that are discovered through LLDP.
E. Register all leaf and spine switches

Show Answer

Question # 35

The FCoE technology is used in a data center and the MDS switches are configured as Fibre Channel Forwarders. What configuration should be applied to an MDS switch in order to be used as the best switch to connect by the CNAs in the fabric?

A. fcoe fcf-priority 1024
B. fcoe fcf-priority 512
C. fcoe fcf-priority 0
D. no fcoe fcf-priority

Show Answer

Question # 36

Refer to the exhibit.  Which two statements describe the routing table of the leaf switch? (Choose two.)

A. The next hop 10.0.8.65 for route 10.20.1.0724 is the TEP address of a border leaf in ACI.
B. The next hop 10.0.1.14 for route 172.16.99.0/24 is the TEP address of a border leaf in ACI.
C. The next hop 10.1.168.95 for route 172.16.100 0/24 is the TEP address of a border leaf in ACI.
D. 172.16.100.0/24 is a BD subnet in ACI.
E. 10.20.1.0/24 is a BD subnet in ACI.

Show Answer

Question # 37

Which two components are used by the Cisco Nexus switches telemetry process? (Choose two)

A. data encoding
B. data manipulation
C. telemetry agent
D. telemetry compression
E. data collection

Show Answer

Question # 38

An engineer must configure SAN connectivity in Cisco UCS manager. The requirement is to specify the WWPN of the storage array and set the zoning type to single initiator multiple targets. The engineer must also configure interrupt handling and queues of the vHBA interface. Which two Cisco UCS policies should be used to configure the settings? (Choose two.)

A. SAN connectivity policy
B. Fibre Channel adapter policy
C. vHBA policy
D. boot policy
E. storage connection policy

Show Answer

Question # 39

A network engineer must configure a Cisco MDS switch to use the local user database for console access if all AAA servers are unreachable. Which configuration should be applied to complete this task? 

A. aaa authentication login default fallback error local
B. aaa authentication login default local
C. aaa authentication login console local
D. aaa authentication login console fallback error local

Show Answer

Question # 40

An administrator needs to configure an automated policy to shut down a link when a given threshold is exceeded on MDS switch. Which feature needs to be used? 

A. Scheduler
B. RMON
C. EEM
D. Call Home 

Show Answer

Question # 41

When the default firmware package is set a new version, which type of policy determines the timing of server reboots during the firmware upgrade?

A. maintenance
B. local disk
C. BIOS
D. diagnostics

Show Answer

Question # 42

Which two authentication types does Cisco UCS Manager support when configuration authentication? (Choose two.)  

A. local
B. LDAP
C. 802.1X
D. Kerberos
E. PAM

Show Answer

Question # 43

An engineer wants to create a backup of Cisco UCS Manager for disaster recovery purposes. What are two characteristics of a full state backup of a Cisco UCS Manager database? (Choose two.) 

A. performs a complete binary dump of the database as a txz file
B. contains all of the configurations
C. performs a complete binary dump of the database as a bin file
D. performs a complete binary dump of the databases as a sql file
E. contains all of the runtime states and statuses but not the configurations

Show Answer

Question # 44

A network engineer is adding a Cisco HyperFlex data platform to the Cisco intersight management portal. Which two components are required for Intersight to claim the Cisco HyperFlex data platform? (Choose two.)

A. device FQDN
B. device public IP address
C. device claim code
D. device ID
E. device serial number

Show Answer

Question # 45

An engineer changed a configuration and must perform a rollback. Which statement applies to a Cisco Nexus 5600 Series switch? 

A. Errors are skipped when an atomic rollback type is triggered.
B. A user who is assigned to the network-operator user role can perform a rollback. 
C. The configuration rollback functionality is disabled when FCoE is enabled.
D. A system checkpoint is generated automatically when the running configuration is saved to NVRAM.

Show Answer

Question # 46

What is an advantage of steaming telemetry over SNMP?

A. MD-5based authentication on polling
B. periodic polling of the device status
C. periodic push-based subscription messages
D. on-change traps sent to a receiver

Show Answer

Question # 47

An engineer is enabling port security on a Cisco MDS 9000 Series Switch. Which feature of enabling port security on a Cisco MDS 9000 Series Switch must be considered? 

A. It always learns about switches that are logging in.
B. It can be distributed by using Cisco Fabric services.
C. It authorizes only the configured sWWN to participate in the fabric.
D. It binds the fabric at the switch level.

Show Answer

Question # 48

Which two statements describe about modifying Cisco UCS user accounts are true? (Choose two.) 

A. The password of the user account must contain a minimum of 10 characters.
B. Disabling a user account maintains all of the data in the Cisco UCS Fabric Interconnect. 
C. Local user accounts override the same account on a remote authentication server, such as TACACS, RADIUS, or LDAP.
D. The password of the user account expires in 30 days.
E. The admin account can be used to log on by using SSH only.

Show Answer

Question # 49

An engineer must connect a Cisco UCS appliance port directly to NFS and iSCSI storage devices. Which action should be taken to achieve this goal?

A. Configure NFS and iSCSI to use the same VLAN tag on the appliance port
B. Configure the appliance ports in access mode and apply VLAN tagging on the storage
C. Configure the appliance ports in trunk mode and apply VLAN tagging on the storage
D. Configure VLAN tagging on the storage and the Cisco UCS simultaneously

Show Answer

Question # 50

An engineer must configure Cisco IMC server management NIC for autonegotiation. Which setting should be selected?

A. Cisco card
B. shared LOM
C. dedicated
D. shared LOM EXT

Show Answer

Question # 51

Refer to the exhibit.  An engineer must monitor all LAN traffic on Fabric A from a blade server. Which source should be configured in the test-span monitor session to complete this task?

A. all vHBAs from the service profile that correspond to this server
B. all uplink FCoE ports
C. all uplink Ethernet ports
D. all vNICs from the service profile that correspond to this server

Show Answer

Question # 52

What are two types of FC/FCoE oversubscription ratios? (Choose two.)A. server storage to end-node count

B. port bandwidth to uplink bandwidth
C. edge ISL bandwidth to core ISL bandwidth
D. host bandwidth to storage bandwidth
E. switch processing power to end-node processing power

Show Answer

Question # 53

A small remote office is set to connect to the regional hub site via NSSA ASBR. Which type of LSA is sent to the remote office OSPF area?

A. type 7 LSA 
B. type 3 LSA
C. type 1 LSA
D. type 5 LSA

Show Answer

Question # 54

Due to new regulatory requirements from a third party, organization ABC must enable twofactor authentication for the Cisco UCS environment. The requirement is also to provide redundancy if the authentication server goes offline. Which three authentication components must be enabled to meet this requirement? (Choose three.)

A. provider group
B. authentication domain
C. TACACS+
D. LDAP
E. local

Show Answer

Question # 55

Port security is statically configured on a Cisco Nexus 7700 Series switch and F3 line card.The switch is configured with an Advanced Services license. Which two actions delete secured MAC addresses from the interface? (Choose Two) 

A. The address must be removed from the configuration.
B. The address must reach the age limit that is configured for the interface.
C. The interface must be converted to a routed port.
D. The device must be restarted manually.
E. Shutdown and then no shutdown must be run on the interface. 

Show Answer

Question # 56

A network engineer must create an EEM script that saves a copy of the running configuration on bootflash and writes a message to syslog when a user saves the configuration to a Cisco Nexus switch. Which configuration set should be applied to complete this task? 

A. Option A
B. Option B
C. Option C
D. Option D

Show Answer

Question # 57

What is an advantage of using Ansible for automation as compared to puppet and chef? 

A. Ansible automates the enforcement of configuration settings.
B. Ansible perform automation without installing a software agent on the target node.
C. Ansible configures a set of CLI commands on a device by using NETCONF.
D. Ansible abstracts a scenario so that set of configuration setting can be used acrossmultiple operating systems.

Show Answer

Question # 58

What is the benefit of adding Cisco HyperFlex Hardware Acceleration Cards to a HyperFlex deployment?

A. offline encryption acceleration
B. increased network throughput
C. GPU acceleration
D. Increased compression efficiency

Show Answer

Question # 59

An engineer is converting a Cisco MDS switch to support NPIV mode. What should be considered when implementing the solution?

A. It must be enabled on VSAN 1 only.
B. It must be enabled globally on all VSANs.
C. It requires mapping of external interface traffic.
D. It requires the FLOGI database to be disabled.

Show Answer

Question # 60

Refer to the exhibit.  Which two statements about the routing table of the leaf switch are true? (Choose two.)

A. The next hop 10.0.1.14 for route 172.16.99.0/24 is the TEP address of a border leaf in ACI.
B. 172.16.100.0/24 is a BD subnet in ACI.
C. The next hop 10.0.8.65 for route 10.20.1.0./24 is the TEP address of a border leaf in ACI.
D. The next hop 10.1.168.95 for route 172.16.100.0/24 is the TEP address of a border leaf in ACI.
E. 10.20.1.0./24 is a BD subnet in ACI.

Show Answer

Question # 61

An engineer configures a role for a new user in Cisco UCS Manager The role should allow the user to configure vHBAs, vNICs, and server port types. Which role should be assigned to allow the engineer to complete this task? 

A. network administrator 
B. operations
C. server-compute
D. AAA administrator

Show Answer

Question # 62

Refer to the exhibit. An engineer must configure FCoE on a Cisco Nexus switch. Which two command sets complete this configuration? (Choose two.) 

A. Option A
B. Option B
C. Option C
D. Option D
E. Option E

Show Answer

Question # 63

A Cisco MDS 9000 series storage Switch has reloaded unexpectedly. Where does the engineer look for the latest core dump file?

A. /mnt/core
B. /mnt/pss
C. /mnt/logs
D. /mnt/recovery

Show Answer

Question # 64

Refer to the exhibit.A flapping link issue has been reported on the vPC keepalive link. A packet capture has been activated on the Cisco Nexus switch. What is the destination IP address of the vPC keepalive packets that are sent by the switch?

A. 192.168.254.4
B. 239.255.70.83
C. 192.168.254.1
D. 192.168.254.2

Show Answer

Question # 65

Refer to the exhibit.  A network engineer plan to upgrade the current software Image of a Cisco nexus switch. What is the impact of starting the EPLD upgrade?

A. The switch reboots multiple times for the new EPLD versions to take effect.
B. The switch reboots one time for the new EPLD versions to take effect.
C. The switch skips the EPLD upgrade for MIFPGA and proceeds with the other EPLD devices.
D. The switch skips the EPLD upgrade for each EPLD device of the switch.

Show Answer

Question # 66

A connect network engineer connects the CAN interface of a server to a switch. The switch must bring down all the vlans on the interface that are not enabled for FCoE, but the Vlans that are enabled for FCoE should continue to carry SAN traffic without interruption. Which configuration should be applied to the switch to achieve this objective?

A. Option A
B. Option B
C. Option C
D. Option D

Show Answer

Question # 67

An engineer must configure a named VSAN when the fabric interconnect is in FibreChannel switch mode The VSAN must meet these requirements:• Named VSAN must be called "VSAN 10".• VSAN ID must be 10.• FCoE ID must be 20.• VSAN 10 must be attached to port 2 in slot 1.Which command set configures a VSAN when the fabric interconnect is in Fibre Channelswitch mode?

A. Option A
B. Option B
C. Option C
D. Option D

Show Answer

Question # 68

Which solution provides remote and direct file-level access to users and systems?

A. direct-attached storage
B. Fibre Channel over Ethernet
C. storage area network
D. network-attached storage

Show Answer

Question # 69

Which statement is true about upgrading the firmware on a Cisco MDS storage switch with dual supervisors?

A. The standby supervisor must be offline before the firmware upgrade begins.
B. Both supervisors load the new firmware and then the active supervisor reboots.
C. Supervisors can be upgraded independently to test the new firmware.
D. The new firmware is load on the standby supervisor first.

Show Answer

Question # 70

A network architect wants to propose a scalable network monitoring solution in which data is repeatedly acquired from network devices. The solution must use a push model and provide close to realtime access to operational data. Which technology must be used to meet these requirements?

A. streaming telemetry
B. logging
C. SNMPv3
D. CLI-based scripting

Show Answer

Question # 71

A UCS B- Series server located in B5108 chassis 1 slot 1 is currently unavailable. The server needs to be associated with a specific service profile when it becomes available. Which associate service profile option should be selected to accomplish this goal? 

A. server pool
B. server
C. custom server
D. restrict migration

Show Answer

Question # 72

Refer to the exhibit.A network engineer is setting up a multihomed OTV network. The first site has been set up with a primary and secondary adjacency server. Which configuration must be added on the remote OTV AEDs site?

A. interface Overlay200otv join-interface Ethernet1/2otv extend-vlan 178, 2500-2563otv use-adjacency-server 20.1.1.1 unicast-only
B. interface Overlay200otv join-interface Ethernet1/2otv extand-vlan 178, 2500-2563otv adjacency-server unicast-only
C. interface Overlay200otv join-interface Ethernet1/2otv extend-vlan 178, 2500-2563
D. interface Overlay200otv join-interface Ethernet1/2otv extend-vlan 178, 2500-2563otv use-adjacency-server 20.1.1.1 20.2.1.1 unicast-only

Show Answer

Question # 73

What is an advantage of NFS as compared to Fibre Channel?

A. NFS enable thin provisioning for LUNs.
B. NFS provides the dynamic allocation of storage capacity.
C. NFS removes the impact of IP overhead.
D. NFS provides direct access to the underlying storage hardware.

Show Answer

Question # 74

APIC EPG Resolution Immediacy is set to “Immediate” Which statement is true about the Deployment Immediacy for VMM domains associated to EPGs?

A. The “Immediate” and “On demand” options require a port group to be created on the VDS.
B. If “On demand” is selected, the policy is programmed in the hardware only when the APIC detects a VM created in the EPG.
C. If “On demand” is selected the policy is programmed in the hardware only when the first packet is received through the data path.
D. If “immediate” is selected the policy is programmed in the hardware as soon as the leaf is booted.

Show Answer

Question # 75

Refer to the exhibit.Which action is taken to ensure that the relay agent forwards the DHCP BOOTREQUEST packet to a DHCP server?

A. Configure the interface of the DHCP server as untrusted.
B. Configure the IP address of the DHCP server.
C. Enable the DHCP relay agent.
D. Verify the DHCP snooping bindings. 

Show Answer

Question # 76

Refer to the exhibit.  Which statement about the ERSPAN configuration in this environment is true.

A. Host A is the source of ERSPAN spanned traffic and host B is the traffic analyzer.
B. Host B is the source of ERSPAN spanned traffic and host A is the traffic analyzer.
C. The session number of the source of ERSPAN spanned traffic must have a session IDof 48 for the traffic analyzer to receive the traffic.
D. The session number of the source of ERSPAN spanned traffic must have a session IDof 47 for the traffic analyzer to receive the traffic. 

Show Answer

Question # 77

Refer to the exhibit.  Service degradation is reported on a VM that is deployed on a Cisco UCS blade server. The traffic from the vNIC is required to SPAN in both directions to a packet analyzer that is connected to UCS-A slot 2 port 12. Which two commands are needed to complete the configuration? (Choose two.)

A. UCS-A /org/service-profile/vnic/mon-src* # set direction both
B. UCS-A /eth-traffic-mon/fabric/eth-mon-session' # create dest-interface 2 12
C. UCS-A /org/service-profile/vnic/mon-src* # set direction receive transmit
D. UCS-A /eth-traffic-mon/fabric/eth-mon-session # activate
E. UCS-A /eth-traffic-mon/fabric/eth-mon-session* # create eth-mon-session/dest-interface 2 12

Show Answer

Question # 78

Refer to the exhibit.  Which action must be taken before the maintenance policy can be committed?

A. Set the soft shutdown timer to a specific time.
B. Associate a service profile to the maintenance policy.
C. Set the policy to apply the change on the next reboot.
D. Specify a maintenance time by selecting a schedule.

Show Answer

Question # 79

An engineer must perform a nondisruptive software upgrade on a dual supervisor Cisco Nexus 7000 series switch. What is the cause of the upgrade being disruptive?

A. The show install all impact command is not issued Before the upgrade
B. The kickstart image is installed by using the install all kickstart image system image command
C. Attempt to simultaneously upgrade more than three cards
D. Change of the configuration settings or the network connections during the upgrade process

Show Answer

Question # 80

An engineer is implementing the Cisco ACI fabric and must create two different vPCs fromleaf switches A and B. The vPCs are deployed as follows:• vPC 1 encompasses ports Eth 1 /1 on leaf A and B and connects to server 1.• vPC 2 encompasses port Eth1/2 on leaf A and B and connects to server 2.A leaf switch profile listing leaves A and B is already configured Which ACI object must be created to meet these requirements?

A. two vPC interface policy groups
B. one access port interface policy group
C. two PortChannel interface policy groups
D. one vPC interface policy group

Show Answer

Question # 81

When a strict CoPP policy is implemented, which statement describes an event during which packets are dropped?

A. Fifteen SSH sessions remain connected to the switch.
B. A large system image is copied to a switch by using the default VRF.
C. A ping sweep is performed on a network that is connected through a switch.
D. A web server that is connected to a switch is affected by a DDoS attack.

Show Answer

Question # 82

Which service profile is affected if the default host firmware policy in Cisco UCS Manager is changed?

A. any service profile that has no host firmware policy defined
B. any service profile that uses a user-created host firmware policy
C. any service profile that is not in the root sub-org
D. any service profile that uses the global-default host firmware policy

Show Answer

Question # 83

Which virtual MAC address is the default for HSRP version 2 group 10?

A. 0000.5E00.0110
B. 0000.0C9F.F010
C. 3719.0351.1C0A
D. 0000.0C9F.F00A

Show Answer

Question # 84

Which configuration statically assigns VSAN membership to a virtual Fibre Channel interface?

A. switch(config-vsan-cb># vsan 100 bind interface fc 3/1
B. switch<config-vsan-db)# vsan 100 bind interface vfc 31
C. switch(config-vsan-db># vsan 100 fc 3/1
D. switch(config-vsan-db)# vsan 100 interface vfc 31

Show Answer

Question # 85

Which two firmware packages are included in the Cisco UCS C-Series Rack-Mount UCSManaged Server Software bundle? (Choose two.)

A. system
B. third-party
C. PSU
D. CIMC
E. BIOS

Show Answer

Question # 86

The engineer must configure SPAN on a cisco Nexus 5000 Series switch to get a capture of the traffic from these applications for an in-depth packet analysis. Which two characteristics must be considered? (Choose two.)

A. The Ethernet, FC, vFC, port channel, SAN port channel can be used as SPAN source ports. 
B. The rx/tx option is available for VLAN or VSAN SPAN sessions.
C. SPAN source port can be monitored in multiple SPAN sessions.
D. Only Ethernet, FC, vFC, port channel port types can be a destination SPAN port.
E. A SPAN source port cannot be a destination SPAN port.

Show Answer

Question # 87

Refer to the exhibit.What is the result of implementing this configuration?

A. The TACACS+ server uses the type-6 encrypted format.
B. The switch queries the TACACS+ server by using a clear text PAP login.
C. The timeout value on the TACACS+ server is 10 seconds.
D. The switch queries the TACACS+ server by using an encrypted text PAP login.

Show Answer

Question # 88

An engineer is duplicating an existing Cisco UCS setup at a new site. What are two characteristics of a logical configuration backup of a Cisco UCS Manager database? (Choose two.)

A. contains the AAA and RBAC configurations
B. contains a file with an extension.tgz that stores all of the configurations
C. contains the configuration organizations and locales
D. contains all of the configurations
E. contains the VLAN and VSAN configurations

Show Answer

Question # 89

Which action must be performed before renumbering a Cisco UCS chassis?

A. Move the chassis to new ports on fibric interconnect.
B. Re-acknowledge the chassis.
C. Decommission the chassis.
D. Run the shut and no shut command on the connected ports.

Show Answer

Question # 90

Which two statements about the process of upgrading an EPLD on a Cisco MDS 9000 series Switch are correct? (Choose two.)

A. The EPLDs for all the modules on a switch must be upgraded at the same time.
B. EPLD upgrades can be completed without powering down the module during the upgrade.
C. EPLDs can be upgraded only to the latest EPLD image.
D. EPLDs can be upgraded without replacing the hardware.
E. An upgrade verification identifies the impact of each EPLD upgrade.

Show Answer

Question # 91

A network engineer must configure a Fibre Channel port monitoring for the local port. The source port should be monitored in the ingress direction. which configuration should be implemented to achieve this objective?

A. Option A
B. Option B
C. Option C
D. Option D

Show Answer

Question # 92

An engineer is implementing OTV on a transport that supports multicast. The solution needs to meet the following requirements:• Establish adjacency to the remote peer by using multicast.• Enable OTV advertisements for VLAN 100 to the other site.Which two commands should be configured to meet these requirements? (Choose two.)

A. otv site-vlan 100
B. otv data-group 232.2.2.0/28
C. otv use-adjacency-server 172.27.255.94
D. otv extend-vlan 100
E. otv control-group 232.1.1.1

Show Answer

Question # 93

An engineer needs to monitor ingress traffic that arrives at interface Ethernet 1/3 that belongs to a Cisco Nexus 5600 Series Switch. The traffic analyzer machine located at interface Ethernet 1/5 is already monitoring other production, and the traffic analyzer must not be impacted by the traffic captured from the interface Eth1/3. The operations team allocated a traffic budget for the new monitoring session of 1 Gbps to meet this requirement Which set of commands configures the SPAN session? 

A. Option A
B. Option B
C. Option C
D. Option D

Show Answer

Question # 94

A network engineer must deploy a configuration backup policy to the cisco UCS manager. The file generated from this backup must have a snapshot of the entire system that should be used to restore the system during disaster recovery. The backup file must be transferred insecurely by using the TCP protocol. Which configuration backup settings meet these requirements?

A. Option A
B. Option B
C. Option C
D. Option D

Show Answer

Question # 95

Refer to the exhibit.  Which setting must be configured to prevent reuse of passwords?

A. No Change Interval
B. Change Interval
C. History Count
D. Change Count

Show Answer

Question # 96

Which statement about the MAC address that the FCoE Initialization Protocol chooses for use by an E-Node in an FCoE implementation is true? 

A. The FCoE Initialization Protocol uses the burned-in MAC address of the converged network adapter for all FCoE operations. 
B. The FCoE Initialization protocol uses a 24-bit FC-MAP and concatenates a 24-bit Fibre Channel ID to create a fibric-provided MAC address. 
C. The FCoE Initialization Protocol uses 01.00.0C as the first 24 bits of the MAC address and appends a 24-bit Fibre Channel ID to derive a full 48-bit FCoE MAC address. 
D. FCoE does not use a MAC address. The FCoE Initialization Protocol is used to acquire a Fibre Channel ID, and the address is used for all FCoE communications in the same way as Fibre Channel Protocol. 

Show Answer

Question # 97

Refer to the exhibit. What is configured as a result of running these commands? 

A. reverse lookup for outbound packets
B. strict unicast RPF
C. loose unicast RPF
D. IP Source Guard

Show Answer

Question # 98

An engineer is seeking the most optimal on demand CPU performance while configuring the BIOS settings of UCS C-series rack mount server.

A. C0/C1 state
B. C6 Retention
C. C2 state
D. C6 non-Retention

Show Answer